Search found 17 matches

Return to advanced search

Re: Juma TRX-2 Firmware v1.20a Build 14

Hi Adrian, Thanks for the v1.20a Build 14 update. The splash screen settings, prompts, and display are correct on the radio. However, with the following radio settings the configuration dump display is as follows: RADIO DISPLAY - CONFIGURATION DUMP Off - Off Juma - ON Juma + Region - USB It looks li...
by AA4PB
17 Apr 2015 22:30
 
Forum: Juma Firmware by 5B4AIY
Topic: Juma TRX-2 Firmware v1.20a Build 14
Replies: 2
Views: 4606

Re: New Firmware for the Juma TRX-2

Thanks for the update, Adrian. I noticed the following difference in displayed System Settings between v1.10q, Build 7 and v1.20a, Build 6: v1.10q Over-Current Trip : 2458 = 2.50A Over-Voltage Trip : 2741 = 14.60V Under-Voltage Trip : 2076 = 11.06V v1.20a Over-Current Trip : 2463 = 2.50A Over-Voltag...
by AA4PB
15 Jan 2015 01:10
 
Forum: Juma Discussion
Topic: New Firmware for the Juma TRX-2
Replies: 2
Views: 4191

Re: How about PSK on a TRX2A?

TF3VS wrote:Are there any readily available information on the internet about operating the TRX2A with the NUE-PSK?
Cable construction, how to connect and tips about setup and operation e.g.

73 Villi
TF3VS


http://www.nikkemedia.fi/juma-trx2/NUE- ... _cable.htm
by AA4PB
30 Apr 2013 13:07
 
Forum: Juma Discussion
Topic: How about PSK on a TRX2A?
Replies: 4
Views: 7500

Re: TRX1 Tune-Up

The guides on the website worked well for me.
by AA4PB
28 Nov 2012 18:49
 
Forum: Juma Discussion
Topic: TRX1 Tune-Up
Replies: 1
Views: 3337

Re: TRX1 DDS Board

You'll need the Microchip MPLAB ICD2 or ICD3 programmer (the ICD3 is the current version from Microchip). You can do on-board programming with it. There is a programming header on the DDS board. You can probably find some information on the TRX2a main page under technical kit information. It may tak...
by AA4PB
28 Nov 2012 17:38
 
Forum: Juma Discussion
Topic: TRX1 DDS Board
Replies: 10
Views: 14018

Re: TRX1 DDS Board

A new part will have no boot loader programmed into it. You can load the progam after the radio is completed IF you have the necessary programmer. The easiest way is probably to get the part pre-programmed from Juma. Once the radio is finished and working you can upgrade the firmware from a PC if de...
by AA4PB
28 Nov 2012 00:59
 
Forum: Juma Discussion
Topic: TRX1 DDS Board
Replies: 10
Views: 14018

Re: TRX1 DDS Board

I lifted a run while replacing the RS232 chip. I used a strand from a piece of stranded wire to make a jumper between the IC pin and the nearest via from the original run. If you look closely you can usually find a nearby connection that you can solder to. For this type of work you really need a tem...
by AA4PB
24 Nov 2012 18:21
 
Forum: Juma Discussion
Topic: TRX1 DDS Board
Replies: 10
Views: 14018

Re: Juma TRX-2 & LDG Electronics Z-817 Autotuner

The original Yaesu CT-62 interface cable contained an MX-232 and a 5V regulator in the 9-pin "D" shell that did the level conversion for the computer. 13.8VDC power was applied to the regulator from the Yaesu radio via one of the mini-DIN conector pins. Given that the Z-817 would require a...
by AA4PB
18 Sep 2012 14:52
 
Forum: Juma Firmware by 5B4AIY
Topic: Juma TRX-2 & LDG Electronics Z-817 Autotuner
Replies: 4
Views: 9601

Re: Juma TRX-2 & LDG Electronics Z-817 Autotuner

After receiving an LDG Z-817 and finding the manual pretty skimpy on technical details for the CAT port I did some further research on the Internet. It appears that while the CAT uses TXD and RXD, it is at TTL levels that are not compatible with a simple cable connection to the TRX2 RS-232 serial po...
by AA4PB
15 Sep 2012 15:43
 
Forum: Juma Firmware by 5B4AIY
Topic: Juma TRX-2 & LDG Electronics Z-817 Autotuner
Replies: 4
Views: 9601

Re: TRX2a Serial Problem

Success!! Replaced R22 with a new 10 Ohm. Actually I jumpered the defective resistor, now reading about 300K, with the 10 Ohm by placing the 10 Ohm at a more convient spot on the top of the PC board. Otherwise I would have had to remove the front panel and the LCD to get access to R22. The RS-232 no...
by AA4PB
10 Jul 2012 22:18
 
Forum: Juma Discussion
Topic: TRX2a Serial Problem
Replies: 13
Views: 16452
Next

Return to advanced search

cron